AEG Welding System 2000 Manuale Utente

1OPERATING INSTRUCTIONSENPROTECT PV 2000AND 2800 ON-GRID SOLAR INVERTERDOC N° 07/08/1002-2 Rev 04

102. FEATURES• Very high conversion efciency (>96%)• MPPT (Maximum Power Point Tracking)• Higher power capacity than similar products of the same

113. INSTALLATION INSTRUCTIONSOPENING THE PACKAGEAfter opening the package, please check the contents of the box. It should contain the following:1.

12MOUNTING PROTECT PV TO THE WALL1. Select a wall or solid vertical surface that can support the PV-Inverter.2. Protect PV requires adequate coo

136. Check the installation conditionsa) Do not install the PV-Inverter on a slanted surfaceb) Check the upper straps of PV-Inverter and ensure i

14CONNECTING TO THE GRID (AC UTILITY)1. Measure grid (utility) voltage and frequency. It should be 230VAC or 220VAC), 50/60Hz, and single phase.2.

15• Connect Phase to pin 1, Neutral to Pin 2 and PE to Pin• Assemble the socket again and attach.• Twist the coupling ring to the PV-Inverters recep

16CONNECT TO PV PANEL (DC INPUT)1. Make sure the maximum open circuit voltage (Voc) of each PV string is less than 450VDC UNDER ANY CONDITION. We r

174. SYSTEM DIAGRAMThe typical connection diagram for the entire PV system is shown in thefollowing fi gure.1. PV-Panel: Provide DC power to Protect P

185. OPERATING YOUR PV-INVERTERMODES OF OPERATIONThere are 3 different modes of operation.1. Normal mode: In this mode, Protect PV works normally. Wh

19• Normal operation: When PV string DC voltage is greater than150V, Protect PV operates in the normal state. In this state, it feeds power to the g

2Before you start 2Safety instructions 4Limited Warranty 51. Overview 92. Features 103. Installation instructions 11 Opening the package

20MAXIMUM POWER POINT TRACKING (MPPT)A good PV inverter must be able to convert the maximum power from any PV panel. Due to its advanced design, Prote

216. INVERTER STATUSProtect PV is designed to be user-friendly; therefore, the status of theInverter can be easily understood by reading the informati

22Feeding current Iac=xx.xAFeeding current amount inxx.x APV array voltage Vdc=xxx.xVInput voltage from PV array,xxx.x VDCSYSTEM FAULTIsolation failur

23INVERTER INFORMATIONModel display MODEL PV 4600 Inverter model, xkW inverter LCD Contrast CONTRASTThe top menu of LCD contrastsettingLCD contrast se

247. COMMUNICATIONSProtect PV is equipped with a powerful communications interface andoptions. Use Protect PV Monitor to monitor the status of your PV

253. Firmware upgrade: To keep the firmware up to-date, use the RS232 port and supplied program to upgrade firmware. To do this, please contact your lo

268. TROUBLE SHOOTINGIn most situations, the Protect PV inverter requires very little service.However, if Protect PV is not able to work perfectly, pl

27• If there is no display on the panel, please check PV-input connections.If the voltage is higher than 150V, call your local service.• During peri

289. SPECIFICATIONSProduct specifications are subject to change without noticeMODELL Protect PV 2000 Protect PV 2800DC INPUTNominal DC voltage360 VDC 3

29TYPICAL EFFICIENCY CHARTS VS. LOADHinweis: Aufgrund von Toleranzen der Testgeräte, Umgebungsbedingungen und Modellspezifikationen können tatsächliche

3BEFORE YOU STARTCongratulations on purchasing your Protect PV 4600 Grid PV-Inverterfrom AEG Power Solutions GmbH referred to in this manual as“PV-Inv

3010. REGULATION & CERTIFICATESINCIDENT FORMCOMPLIANCE & STANDARDSEMC:DIN EN 50081, part 1 (EMV-interference emission) (EN 55014, EN60555 part

31

32AEG Power Solutions GmbHEmil-Siepmann-Str. 3259581 Warstein-Belecke - GermanyTel.: +49 (0) 2902 763-520/-290 - Fax: +49 (0) 2902 763-1201www.aegpowe

4RISK OF ELECTRIC SHOCK1. Do not remove the casing. Protect PV® contains no user serviceable parts. Refer servicing to qualified service personnel.Bo

5LIMITED WARRANTYThe limited warranty provided by AEG Power Solution (“AEG PS”) in this Statement of Warranty applies only to Equipment purchased for

6accidents brought about by the Purchaser‘s actions, such as negligence, connection error, failure to follow instructions for maintenance, abnor-mal u

7EXCLUSIONSAEG PS shall not be liable under the Warranty if its testing and exa-mination discloses that the alleged defect in the Equipment does not e

8WARRANTY EXTENSIONThe original factory warranty can be extended by purchasing additionalExtended Warranty Program which extends factory warranty by fi

91. OVERVIEWProtect PV 2000 & 2800DISPLAYINFORMATION SWITCHLCD DISPLAY:SHOWING THE INVERTER STATUSSOLAR PANELINPUTRS232 COVERRS485 SLOTUTILITY (AC