Aeg L 98485 FL Manuale Utente

L 98685 FLL 98485 FLWASHING MACHINE USER MANUAL

•The time of delay– When you set the delayed start the time of the programme end in-creases by steps of 30 minutes till 10 hours and by steps of oneho

Rinse hold1) Only available for Spin/Drain programme.JThe default temperature of the programme.Cold washDAMPF BUTTON 4Touch button 4 to set the steam

The appliance soaks the laundry at 30°Cfor about half an hour before to wash.SPIN BUTTON 11Touch button 11 to:• Decrease the maximum speed of thespin

WASHING PROGRAMMESProgramme Temperature Type of loadWeight of loadProgrammedescriptionFunctionsKoch/Bunt 95° - Cold White and col-oured cottonwith hea

Programme Temperature Type of loadWeight of loadProgrammedescriptionFunctionsFeinwäsche 40° - ColdRinsesShort spinDelicate fabricsas acrylics, vis-cos

Programme Temperature Type of loadWeight of loadProgrammedescriptionFunctionsSpülen 0° All fabricsMaximum load 8kgRinse with ad-ditivesSpin phaseSPIN

5) The default spin speed is for cotton items. Set the spin speed applicable with your laundry.6) If you select this function the appliance performs o

Programme1)Energy consumption(KWh)2)Water consump-tion (litre)2)Cotton 40 °C economy3)0.70 57The cotton 60 °C economy and cotton 40 °C economy are the

BEFORE FIRST USE1.To activate the drain system, put 2 li-tre of water in the main wash com-partment of the detergent dispenser.2.Put a small quantity

USING THE APPLIANCE1.Open the water tap.2.Connect the mains plug to the mainssocket.ACTIVATING THE APPLIANCE AND SETTING A PROGRAMMEFor a correct oper

SERVICEWhen contacting Service, ensure thatyou have the following data available.The information can be found on therating plate.ModelPNCSerial Numbe

Make sure not to have the laundry out ofthe drum between the seal and the door.There is the risk of water leakage or dam-age laundry.USING THE DETERGE

Check the position of the flap1.Pull out the detergent dispenser untilit stops.2.Press the lever down to remove thedispenser.3.To use powder detergent

You cannot set the delay start withthe Steam programme.22

STARTING A PROGRAMME1.Touch button 6 to start the pro-gramme. The indicator of button 6stops to flash and is on with red col-our.If a delayed start is

7.Remove the laundry from the appli-ance. Make sure that the drum isempty.8.Keep the door ajar, to prevent mil-dew and odours.9.Close the water tap.Th

HELPFUL HINTS AND TIPSTHE LAUNDRY LOAD• Divide the laundry in: white, coloured,synthetics, delicates and wool.• Obey the washing instructions that are

Level TypeWater hardness°dH °T.H. mmol/l Clarke2 medium 8-14 16-25 1.6-2.5 10-163 hard 15-21 26-37 2.6-3.7 17-254 very hard > 21 > 37 >3.7 &g

CARE AND CLEANINGWARNING!Disconnect the appliance from the mainssupply before you clean it.DESCALINGThe water we use contains limescale. If itbecomes

DETERGENT DISPENSERTo clean the dispenser:121.Press the lever.2.Pull the dispenser out.3.Remove the top part of the liquid ad-ditive compartment.4.Cle

To clean the drain pump:1.Open the drain pump door.2.Pull the flap out to remove it.3.Put a container below the recess ofthe drain pump to collect the

FOR PERFECT RESULTSThank you for choosing this AEG product. We have created it to give youimpeccable performance for many years, with innovative techn

129.Clean the filter under the water tapand put it back in the pump into thespecial guides.10.Make sure that you tighten correctlythe filter to preven

1.Put 2 litres of water in the main washcompartment of the detergent dis-penser.2.Start the programme to drain the wa-ter.FROST PRECAUTIONSIf the appl

TROUBLESHOOTINGThe start of the appliance does not occuror it stops during operation.Try to find a solution to the problem be-fore you contact the ser

PROBLEM WITHOUT ALARM MESSAGEProblem Possible cause Possible solutionThe appliancedoes not drainthe water.A washing programmewithout the drain phaseis

Problem Possible cause Possible solution You did not remove thepackaging and/or thetransit bolts.Remove the packaging and/orthe transit bolts. Refer

INSTALLATIONUNPACKING1.Use the gloves. Remove the externalfilm. If necessary, use a cutter.2.Remove the cardboard top.3.Remove the polystyrene packagi

6.Put one of the polystyrene packagingelements on the floor behind the ap-pliance. Carefully put down the appli-ance with the rear side on it. Makesur

12.Put the plastic caps in the holes. Youcan find these caps in the user man-ual bag.WARNING!Remove all the packaging and thetransit bolts before you

THE INLET HOSE20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rec

With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide cannotmove when the appliance drains. At-tach the guide to the

SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environmen

You can extend the drain hose tomaximum 400 cm. Contact theservice centre for the other drainhose and the extension.40

ENGLISH41

42

ENGLISH43

www.aeg.com/shop 132940553-B-382011

To replace the internal lamp, con-tact the service centre.Disconnect the mains plug fromthe mains socket before the re-placement of the internal lamp.

ENVIRONMENT CONCERNSPACKAGING MATERIALSRecycle the materials with the symbol .Put the packaging in applicable contain-ers to recycle it.ECOLOGICAL

PRODUCT DESCRIPTION1 2 3910578411121361Worktop2Detergent dispenser3Control panel4Door handle5Internal lamp6Rating plate7Drain pump8Feet for the applia

CONTROL PANELWolle/SeideKoch/BuntExtra LeisePflegeleichtLeichtbügelnFeinwäscheDaunenAnti-Allergie Schleudern/Pumpen SpülenJeans 20Min. - 3kgSuper

DISPLAY 3ABCDEFGHIJAThe text bar:• Guides you in the use of the appliance.• Shows the programme status and phase.• Shows alarm messages. Refer to &apo