Aeg COMPACT READER ARE I2 Manuale Utente Pagina 26
- Pagina / 33
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Manual
Page 26 / 33- Revision 01
ARE I2 / RS 232 – Installation Guide
AEG
Identifikationssysteme GmbH
Söflinger Straße 100
D-89077 Ulm
Tel. ++49(0)731-933-1340/1877
Fax ++49(0)731-933-1855
e-mail: [email protected]
7.2 Operating Mode 0 - Continuous Reading
When operating continuously the exciter is switched on permanently. The reading cycles
are initiated periodically.
After an accomplished reading cycle the reading information is evaluated. After that data (ei-
ther transponder number or NoRead code) is output to the serial interface
Figure 7.2: continuous operation
7.2.1 Settings of the Reader / Most Used Parameters
The default operation mode is changed by sending a software command to the reader.
In combination with an R / W transponder, the serial number of the transponder device is read
out only.
MD 0 - continuos read
most used parameters.
• CID 0 - no suppression of repeatedly read Ids
• CN 0 - no suppression of NoReads
exciter
processor
interface
reading cycle
ID ID ID
reading cycle reading cycle
- Compact Reader ARE I2 1
- Installation Guide 1
- Serial Interface (RS 232) 1
- Contents 2
- Page 4 / 33- Revision 01 4
- 1 Introduction 5
- 2 System Overview 5
- 3 Start-up Procedure 6
- 4 Installation 7
- 4.1 Mounting of the Housing 7
- 4.2 Grounding of the Reader 7
- Page 8 / 33- Revision 01 8
- Page 9 / 33- Revision 01 9
- 4.3.6 Plug in of the SAB Cab 11
- RxD (reader) 12
- TxD (reader) 12
- 4.4 Power Supply 13
- 5 Visual Signal Lamps 14
- 6.1 General 15
- 6.2 Error Codes 16
- 6.5 NID- Failure Protection 17
- Page 18 / 33- Revision 01 18
- 6.6 EC- Echo 19
- 6.7 BD- Baudrate 19
- 6.9 VS- Show Parameter 20
- 6.10 VSAVE – Save Parameter 20
- Page 21 / 33- Revision 01 21
- Page 22 / 33- Revision 01 22
- 7.1.3 ReadOnly-Transponder 23
- 7.1.4 R / W –Transponder 23
- 7.1.4.2 Selective Read RD 24
- Page 25 / 33- Revision 01 25
- Page 26 / 33- Revision 01 26
- Page 27 / 33- Revision 01 27
- 8 Instructions 28
- Page 29 / 33- Revision 01 29
- 9 Hotline 30
- 10 Reference Documentation 30
- 11 Revisions 30
- 12 Appendix 31
- Page 32 / 33- Revision 01 32
- Page 33 / 33- Revision 01 33
Kontron ETX-Starterkit manuály
Uživatelské manuály a uživatelské příručky pro Hardware Kontron ETX-Starterkit.
Poskytujeme 1 manuály pdf Kontron ETX-Starterkit ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale